Handmade cards with hanging heart Christmas tree decoration

These Christmas cards combine techniques from two of last year's craft projects to make a lovely Christmas card with a removable Christmas tree decoration.

They're very simple and all you need is

• White card
• Wrapping paper
• PVA glue
• Wool or string
• Needle

1. Begin by ripping the wrapping paper into smallish pieces. If the paper has words or motifs on it, such as snowmen, try to keep a few of these whole and put them to one side.

2. Fold the white card down the middle

3. Draw a heart on the front and cut this out - both the heart and the hole are needed

4. Take the cardboard heart, pieces of paper, and pva glue and begin building up layers of paper over it as in Paper mache Christmas decorations

5. After a couple of layers, and while the glue/paper is still wet and soft, push the needle through the heart where it will hang from.

6. Let the glue dry, then add a final layer using the pieces that you put aside earlier.

7. Push the needle through the hole again

8. On the inside of the folded card, lightly draw a slightly larger heart around the heart shaped hole

9. Follow the instructions for Sew simple Christmas cards to stitch the outline

10. Thread wool through the hole in the heart decoration

11. Line the heart decoration up with the cut out heart, and make a hole in the back of the card so that heart can hang - tie the string loosely at the back so that it can be untied and hung on a tree later

12. Write your greeting on the front and you're done



Christmas tree baubles

This is a bit of an addition to my Paper mache Father Christmas decorations, rather than a completely new post or idea.

Basically you follow the instructions in the Paper mache Father Christmas decorations post to create a solid paper mache base, but then instead of proceeding to paint it pink and turn it into Father Christmas, we go down a very slightly more tasteful route!

You will need
 

• Pva glue mixed with a dash of water
• Paintbrush or spatular
• Christmas wrapping paper
• A paper mache bauble (see Paper mache Father Christmas decorations )
• Need and string

Begin by carefully ripping out motifs from your Christmas paper - e.g. a whole reindeer or penguin, the words Merry Christmas, or whatever is on your paper.

Set these aside, they go on last to ensure that they remain whole and are not covered by other layers.

Now rip the rest of your Christmas paper up any way you like.

Cover your bauble with glue and then build up a layer of Christmas paper.

Once the whole bauble is covered with bright Christmas paper, add the pieces you set aside earlier as a final layer, trying to keep the motifs whole.

Finally, once dry, take your needle and firmly, but slowly, push it through the top of the shell and pull string through to create a hanging loop.

Then you're done!

Paper mache Father Christmas decorations

So these are simple paper mache decorations, built from scratch using nothing but scrap paper and then decorated with felt.

However, they are also my revenge Christmas decorations! Every time my mum visits she brings more and more toys and bag loads of plastic tat, which subsequently ends up strewn across my living room.

As way of thanks, little Nutmeg and I are making her lots of very beautiful Christmas decorations which I am sure she will treasure (and feel obliged to display!)

As each layer is added it will need to dry, so this is a project that we have been adding bits to every day this week. (Perfect for a 3 year old who gets bored quickly as she can do a little bit each night)

You will need

• PVA glue mixed with a dash of water
• Paint brush or glue spatula
• Balloon (or water bomb for nice round shape)
• Scrap newspaper or brown paper
• Pink paint or pink paper
• 1 sheet of red and 1 sheet of white felt (or thick paper)
• Black pen
• Scissors
• Toilet roll tubes (optional)

Getting started

Blow up your balloon to the desired size. My decorations are going to be hung on a tree, so were kept quite small, but there is no reason why you couldn't go BIGGER!

Mix some PVA glue with a little water

Rip up your scrap paper into small pieces (it is important that it is torn and not cut so that the edges blend better)

Next begin covering your balloons in glue and then paper, painting each piece of paper with glue as you go

Once the balloon is covered in paper, it's ok to add a second layer of paper immediately.

After this, place your balloon on a toilet roll while it dries (avoid it sticking to the table etc)

Once completely dry it's time to burst and remove the balloon...

Make sure that you are holding the end of the balloon as you burst it to ensure that the balloon doesn't fall inside your decoration.

Then gently wiggle it out through the hole.

At this point your decoration should be quite firm, but would benefit from a couple more layers to give it extra strength and to cover the exit hole.

Paint the whole decoration with glue and add 1-2 more layers of paper.

Standing the decoration on a toilet roll tube may make this easier and avoid sticky fingers.

After letting decorations dry over night, either paint pink them or cover them in pink paper

Either way, they will need to dry again...

Now for decoration

To make the hat, draw a circle on the red felt/paper and cut it out.

Cut this in half and then wrap it around to create a cone. Gluing down the seam.

Add a strip of white along the bottom and then add details like a beard, mouth, eyebrows and eyes

My final step will be to put a piece of white wool through the hats so that they can be hung on a Christmas tree.

Alternatively you could colour/decorate the toilet roll tube and display your Father Christmas as a standing decoration.

With the 3rd balloon we covered, we will be making an angel/fairy for the top of the tree next week. Isn't my Mum a lucky Grandma!!!

(Please see also a slightly more tasteful version of this craft project where the baubles are covered in Christmas wrapping paper - Christmas tree baubles )

Sew simple, homemade Christmas cards

Sew simple Christmas cards (made by a 3 year old)

Christmas is coming and my daughter is at home with me (and her baby brother) 2 days a week, so I am always looking for things we can do together.

It's an extra bonus if it isn't messy and makes something that you might actually want at the end of it! I think this ticks both of these boxes.

Today we made Christmas cards from blank cards and scraps of coloured wool.
Megan is only 3 and hers came out good enough to send (with help of course) so I am sure older children will enjoy this and be able to create their own designs too.

You will need...

• Blank cards and envelopes (mine were from John Lewis)
• Pencil
• Bodkin (not very sharp wool needle)
• Coloured wool
• Merry Christmas stickers/stamp (optional - especially if your children are old enough to write, my stamp was from John Lewis)

Let's do it...

Begin by drawing out your design on the blank card. As wool is quite thick it is ok to do this on the right side (front) of the card, the wool will cover any lines.

 



Next take your needle and make guide holes through the card evenly around the design. This will make sewing much simpler and mean that your child is only gently pushing the needle through an existing hole rather than needing to force it through the card.

Now begin to sew between the existing holes. This should be done using back stitch where you skip a hole, and then work back to the previous hole filling in a gap. The next stitch is then started from end of the previous stitch. (repeat)

 

It is not essential that back stitch is used, but this avoids oversewing the whole design twice and means the back of the design shouldn't be too untidy

 

 

Finally tie off any loose ends and add a greeting of your choice.

 

Simple but I'm sure our family will like receiving cards Megan has made herself.